Not Logged in - No Account?
Logging in allows you to post to forums, track new posts, subscribe to threads, pm (private message) other members, and receive periodic news letters. Once logged in this message disappears. No account? Create one by registering here. Lost your password, request a new password. We respect your privacy and collect minimal information when you register and we do not resell that information or use it in any objectionable way. You can review our privacy policy for details.
ZAP configuration
Hi there,
I've done my best with trixbox and all is working fine but I'm stuck with the ZAP parameters.
I can't make and receive calls using ZAP channels.
I thing I'm pretty close to the solution and I need and expert eye to find out where I'm wrong.
Actually, it is even worse : when I'm placing a call using a zap trunk it rings on the analog phone on the channel 1 !!!
What could I change to make it work properly ?
Any suggestion is good for me...
Thanks in advance !
Here is my configuration :
2 SIP accounts and 4 softphones, working very well !
Digium TDM400 2FXO 2FXS :
- 1 analog phones on channel 1 (FXS)
- 2 pstn lines on channels 3 & 4 (FXO)
- 2 trunks (1 for each pstn line) : zap/3 et zap/4
- 1 inbound route "any CID / any DID"
- 2 inbound routes : 1 for each zap trunk (do I have to ?)
________________________________________________
*** zapata-auto.conf ***
; Autogenerated by /usr/sbin/genzaptelconf -- do not hand edit
; Zaptel Channels Configurations (zapata.conf)
;
; This is not intended to be a complete zapata.conf. Rather, it is intended
; to be #include-d by /etc/zapata.conf that will include the global settings
;
; Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1" (MASTER)
;;; line="1 WCTDM/0/0"
signalling=fxo_ks
callerid="Channel 1" <6001>
mailbox=6001
group=5
context=from-internal
channel => 1
callerid=
mailbox=
group=
context=default
;;; line="2 WCTDM/0/1"
signalling=fxo_ks
callerid="Channel 2" <6002>
mailbox=6002
group=5
context=from-internal
channel => 2
callerid=
mailbox=
group=
context=default
;;; line="3 WCTDM/0/2"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 3
context=from-zaptel **(I changed from "default" to this value)
;;; line="4 WCTDM/0/3"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 4
context=from-zaptel **(I changed from "default" to this value)
; Span 2: ZTDUMMY/1 "ZTDUMMY/1 (source: RTC) 1"
________________________________________________
*** zapata.conf ***
;
; Zapata telephony interface
;
; Configuration file
[trunkgroups]
[channels]
busydetect=yes
busycount=6
language=en
context=from-zaptel
signalling=fxs_ks
rxwink=300
;
; Whether or not to do distinctive ring detection on FXO lines
;
;usedistinctiveringdetection=yes
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=no
;echotraining=800
rxgain=4.0
txgain=2.0
group=0
callgroup=1
pickupgroup=1
immediate=no
;faxdetect=both
faxdetect=incoming
;faxdetect=outgoing
;faxdetect=no
;Include genzaptelconf configs
#include zapata-auto.conf
group=0 **(what does this refer to ?)
;Include AMP configs
#include zapata_additional.conf
________________________________________________
*** zapatal_additional.conf ***
;;;;;;[110]
signalling=fxo_ks
record_out=Adhoc
record_in=Adhoc
mailbox=110@device
immediate=no
echotraining=800
echocancelwhenbridged=no
echocancel=yes
dial=ZAP/1
context=from-internal
callprogress=no
callerid=device <110>
busydetect=no
busycount=7
accountcode=
channel=>1
You have your connections
You have your connections flipped on the card for port 1-4. If when you attempt to dial out your analog phone rings then the most common mistake is that phone is plugged into the trunk port. Flip your connections around.